Faculty of Mechanical Engineering: Recent submissions

  • The Effects of Car A-Pillar and Windshield Geometry on Local Flow and Noise 
    Alam, Dr. Firoz (RMIT University, Melbourne, Australia., 2000-09)
    A desirable requirement in the production of modern vehicles world-wide is the provision of a high level of driving comfort. An important aspect of this is the minimisation of aerodynamic noise. As structure-borne, engine, ...
  • Impingement Heat Transfer Due to Circular Air Jet Over Rough Flat Surfaces 
    Islam, Md. Nurul (Bangladesh Institute of Technology (BIT), Khulna, 2000-08)
    An experimental investigation was carried out to investigate the pressure distribution and the local and average Nusselt number due to impinging of a circular air jet over uniformly heated rough flat surfaces. The present ...
  • Study of Mechanical Behaviour of Jute Fibre Reinforced Plastics 
    Kazim, K. A. (Bangladesh University of Engineering and Technology (BUET), Dhaka, Bangladesh., 1986-09)
    Some strength characteristics of jute fibres, yarns, fibre bundles, yarn bundles, mats, and jute mat reinforced plastics, have been determined. The hardness, fatigue life, flexural modulus and percentage increase in ...
  • Flow and Heat Transfer Characteristics of Wall Jet over Rough Surfaces 
    Kader, Md. Golam (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2003-01)
    Experimental investigation were carried out to verify the pressure distribution and the local Nusselt number due to circular wall jet over uniformly heated rough flat surfaces. The present investigation shows the ...
  • Design Construction and Performance Test of a Short Length Subsonic Wind Tunnel 
    Arifuzzaman, Md. (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2012-09)
    Wind engineering is a field that has been evolving over centuries. Wind engineering is based on using measurements of actual wind flows to predict the forces transferred to engineering structures and machines. A large ...
  • Effect of Surfactant on Water Vapor Absorption into Aqueous Lithium Bromide 
    Bari, Md. Abdullah Al (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2012-09)
    The objective of the present study is to investigate the absorbing characteristics of water vapor in LiBr-H2O (weak solution) and also the enhancement of absorption in presence of a surfactant in the absorber of a vapor ...
  • Experimental Investigation on an Intermittent Ammonia Absorption Refrigeration System 
    Mondal, Dipayan (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2014-09)
    This project work describes the experimental investigation on an intermittent ammonia absorption refrigeration system which consists of a generator/ absorber, a condenser, an evaporator and an expansion valve. The system ...
  • Flow Separation Control on a NACA 0015 Airfoil using Co-Flow Jet (CFJ) Flow 
    Hossain, Md Amzad (2013-12)
    This thesis describes the effort to experimentally verify the high performance characteristics of the co-flow jet (CFJ) airfoil. The CFJ utilizes tangentially injected air at the leading edge and tangentially removed air ...
  • Development of a Low Cut-In Speed Wind Turbine 
    Ferdous, Mausumi (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2012-09)
    Wind energy systems have become a focal point in the research of renewable energy sources. In this research provides a new concept of high performance, low cut-in speed wind turbine blade. To design the wind turbine ...
  • Occupational Safety Problems in Bangladesh Ship breaking Industry - a case study 
    Kamruzzaman, Abu Sayed Md (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2007-12)
    Ship breaking is one of the most hazardous and dangerous occupation. Grave concern about the occupational safety and health problems caused by ship dismantling has been widely reported . Whilst many press articles have ...
  • Extraction of Pyrolytic Fuel from Nonbiodegradable Solid Waste 
    Ali, Md. Hasan (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2013-11)
    Under the project work waste tire and tube of bicycle/rickshaw were converted to useful fuel oil by the process of pyrolysis. In doing so fixed bed lire tube heating pyrolysis technology has been applied. Thermal pyrolysis ...
  • Experimental Study of Flow Separation Control on an Airfoil by Suction and Injection 
    Hossain, Md. Farhad (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2010-05)
    In this research a new concept of flow separation control mechanism has been introduced to improve the aerodynamic characteristics of an airfoil. Control of flow separation over an airfoil which experiences a laminar ...
  • Plant Layout of Cement Industry for Mass Production 
    Alam, Md.Ekhtiar (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2010-08)
    Plant layout is the lifeblood of an industry as well as of any cement industry for its manufacturing process and layout design. A cement industry uses various types of machinery and equipment for its smooth operation. ...
  • Optimization of Vehicle Routing in a Supply Chain 
    Mondol, Md. Kburram Bin Abdul Kayum (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2009-09)
    Supply chain is a sequence of organizations- their facilities, functions and activities that are involved in producing and delivering a product or service. The sequence begins with basic suppliers of' raw materials and ...
  • Development of Maintenance Plan (Case study : Eastern Jute mills Ltd, Khulna.) 
    Ghosh, Suvendra kumar (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2012-06)
    Maintenance acts like the heart of the machine. Due to running, every machine Undergoes wear and tear due to friction. Maintenance of a machine consists of all the Various activities required to keep machine in standard ...
  • Analysis of the Major Causes of Accident and Standardize the Safety Measures for the Electricity Distribution System. 
    Islam, Md. Siful (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2009-03)
    Electricity distribution is a vast sector and it is stretched out over the whole country. Huge quantity of distribution line, line equipment, workers and public are involved in the system. The activities of the distribution ...
  • Optimization of Multi-Item Inventory System 
    Talapatra, Subrata (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2009-09)
    Inventory is the lifeblood of a business organization. Industry uses various types of materials for its smooth running. A significant amount of total assets is invested as inventory. In many companies, the management has ...
  • Studies on Some Aspects of Electrochemical Grinding 
    Bhowmick, Tarapada (Indian Institute of Technology (IIT), Kharagpur, India, 1999-08)
    Electrochemical grinding (ECG) has become more and more important for its industrial use, in machining problems associated with grinding hard and wear resisting and even very soft electrically conductive materials. In a ...
  • Some Studies on Heat Transfer in Circulating Fluidized Beds 
    Moral, Md. Nawsher Ali (Indian Institute of Technology (IIT), Kharagpur, India, 1990-12)
    Experimental investigations were made to study the effect of fin and vertical probe height on hydrodynamics and heat transfer in circulating fluidized beds (CFB). The experiments were conducted in a 100 mm I.D., 5.15 m ...
  • Laminar Slot Jet and Slot Jet Impingement Heat Transfer 
    Hossain, Khandkar Aftab (Indian Institute of Technology (IIT), Kharagpur, India., 1996)
    In this investigation, the numerical solutions of Navier-Stokes equations and energy equation are presented for (1) laminar free slot jet, (ii) laminar free axisymmetric jet, (iii) laminar jet impingement on a circular ...

Search KUET IR


Browse

My Account