KUET Institutional Repository

Faculty of Mechanical Engineering

Faculty of Mechanical Engineering

 

The academic departments of the university offer degree programs in different engineering, and science disciplines. All the departments except Dept. of Humanities have the postgraduate programs, while the departments of Civil Engineering, Electrical and Electronic Engineering,Mechanical Engineering, Computer Science and Engineering, Electronics Communication Engineering , Industrial Engineering and Management offer undergraduate degree programs.

For more information

Sub-communities within this community

Recent Submissions

  • Pervin, Mst. Shahin Akter (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2006-12)
    The performance parameters like the coefficient of discharge Cd and the spray cone Angle W of a swirl spray solid cone nozzle without a vane swirler have been studied numerically. The numerical computation of flow through ...
  • Rahman, Dr. A. N. M. Mizanur (Indian Institute of Technology (IIT), Kharagpur, India., 1997-09)
    Assessment of techno-economic viabiity of solar energy systems is based on long term performance. The popular design methods for active as wel1 as passive solar energy systems require certain proprocessed parameters in ...
  • Alam, Dr. Firoz (RMIT University, Melbourne, Australia., 2000-09)
    A desirable requirement in the production of modern vehicles world-wide is the provision of a high level of driving comfort. An important aspect of this is the minimisation of aerodynamic noise. As structure-borne, engine, ...
  • Islam, Md. Nurul (Bangladesh Institute of Technology (BIT), Khulna, 2000-08)
    An experimental investigation was carried out to investigate the pressure distribution and the local and average Nusselt number due to impinging of a circular air jet over uniformly heated rough flat surfaces. The present ...
  • Kazim, K. A. (Bangladesh University of Engineering and Technology (BUET), Dhaka, Bangladesh., 1986-09)
    Some strength characteristics of jute fibres, yarns, fibre bundles, yarn bundles, mats, and jute mat reinforced plastics, have been determined. The hardness, fatigue life, flexural modulus and percentage increase in ...
  • Kader, Md. Golam (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2003-01)
    Experimental investigation were carried out to verify the pressure distribution and the local Nusselt number due to circular wall jet over uniformly heated rough flat surfaces. The present investigation shows the ...
  • Arifuzzaman, Md. (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2012-09)
    Wind engineering is a field that has been evolving over centuries. Wind engineering is based on using measurements of actual wind flows to predict the forces transferred to engineering structures and machines. A large ...
  • Bari, Md. Abdullah Al (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2012-09)
    The objective of the present study is to investigate the absorbing characteristics of water vapor in LiBr-H2O (weak solution) and also the enhancement of absorption in presence of a surfactant in the absorber of a vapor ...
  • Mondal, Dipayan (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2014-09)
    This project work describes the experimental investigation on an intermittent ammonia absorption refrigeration system which consists of a generator/ absorber, a condenser, an evaporator and an expansion valve. The system ...
  • Hossain, Md Amzad (2013-12)
    This thesis describes the effort to experimentally verify the high performance characteristics of the co-flow jet (CFJ) airfoil. The CFJ utilizes tangentially injected air at the leading edge and tangentially removed air ...
  • Ferdous, Mausumi (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2012-09)
    Wind energy systems have become a focal point in the research of renewable energy sources. In this research provides a new concept of high performance, low cut-in speed wind turbine blade. To design the wind turbine ...
  • Kamruzzaman, Abu Sayed Md (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2007-12)
    Ship breaking is one of the most hazardous and dangerous occupation. Grave concern about the occupational safety and health problems caused by ship dismantling has been widely reported . Whilst many press articles have ...
  • Ali, Md. Hasan (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2013-11)
    Under the project work waste tire and tube of bicycle/rickshaw were converted to useful fuel oil by the process of pyrolysis. In doing so fixed bed lire tube heating pyrolysis technology has been applied. Thermal pyrolysis ...
  • Hossain, Md. Farhad (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2010-05)
    In this research a new concept of flow separation control mechanism has been introduced to improve the aerodynamic characteristics of an airfoil. Control of flow separation over an airfoil which experiences a laminar ...
  • Alam, Md.Ekhtiar (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2010-08)
    Plant layout is the lifeblood of an industry as well as of any cement industry for its manufacturing process and layout design. A cement industry uses various types of machinery and equipment for its smooth operation. ...
  • Mondol, Md. Kburram Bin Abdul Kayum (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2009-09)
    Supply chain is a sequence of organizations- their facilities, functions and activities that are involved in producing and delivering a product or service. The sequence begins with basic suppliers of' raw materials and ...
  • Ghosh, Suvendra kumar (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2012-06)
    Maintenance acts like the heart of the machine. Due to running, every machine Undergoes wear and tear due to friction. Maintenance of a machine consists of all the Various activities required to keep machine in standard ...
  • Islam, Md. Siful (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2009-03)
    Electricity distribution is a vast sector and it is stretched out over the whole country. Huge quantity of distribution line, line equipment, workers and public are involved in the system. The activities of the distribution ...
  • Talapatra, Subrata (Khulna University of Engineering & Technology (KUET), 2009-09)
    Inventory is the lifeblood of a business organization. Industry uses various types of materials for its smooth running. A significant amount of total assets is invested as inventory. In many companies, the management has ...
  • Bhowmick, Tarapada (Indian Institute of Technology (IIT), Kharagpur, India, 1999-08)
    Electrochemical grinding (ECG) has become more and more important for its industrial use, in machining problems associated with grinding hard and wear resisting and even very soft electrically conductive materials. In a ...

View more