M.Sc. Engg.

 

Recent Submissions

  • Rahman, Md. Sumon (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2019-12)
    The construction activities are closely associated with many occupational injuries. Work-related musculoskeletal disorders (WMSDs) are the most common occupational injuries faced by construction workers. WMSDs refer to a ...
  • Karmokar, Sandip (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2019-05)
    Erosive wear can as defined as solid deduction process from a solid superficial due to frictional action between the slurry and surface. It is triggered by the effect of solid particles contains by slurry in contradiction ...
  • Rahman, Md. Mahbubur (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2019-06)
    The multi-objective assignment problem is basically the N men –N tasks problem, where a single task has to be assigned to an individual with a view of optimizing the outcomes. A common challenge is to address the conflicting ...
  • Pushpo, Faria Haque (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2018-12)
    This paper represents a brief overview on the evaluation of qualitative and quantitative techniques in decision-making. The purpose of this study was to examine the status and extent to which administrators and engineers ...
  • Pervin, Mst. Shahin Akter (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2006-12)
    The performance parameters like the coefficient of discharge Cd and the spray cone Angle W of a swirl spray solid cone nozzle without a vane swirler have been studied numerically. The numerical computation of flow through ...
  • Islam, Md. Nurul (Bangladesh Institute of Technology (BIT), Khulna, 2000-08)
    An experimental investigation was carried out to investigate the pressure distribution and the local and average Nusselt number due to impinging of a circular air jet over uniformly heated rough flat surfaces. The present ...
  • Kazim, K. A. (Bangladesh University of Engineering and Technology (BUET), Dhaka, Bangladesh., 1986-09)
    Some strength characteristics of jute fibres, yarns, fibre bundles, yarn bundles, mats, and jute mat reinforced plastics, have been determined. The hardness, fatigue life, flexural modulus and percentage increase in ...
  • Kader, Md. Golam (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2003-01)
    Experimental investigation were carried out to verify the pressure distribution and the local Nusselt number due to circular wall jet over uniformly heated rough flat surfaces. The present investigation shows the ...
  • Arifuzzaman, Md. (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2012-09)
    Wind engineering is a field that has been evolving over centuries. Wind engineering is based on using measurements of actual wind flows to predict the forces transferred to engineering structures and machines. A large ...
  • Bari, Md. Abdullah Al (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2012-09)
    The objective of the present study is to investigate the absorbing characteristics of water vapor in LiBr-H2O (weak solution) and also the enhancement of absorption in presence of a surfactant in the absorber of a vapor ...
  • Mondal, Dipayan (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2014-09)
    This project work describes the experimental investigation on an intermittent ammonia absorption refrigeration system which consists of a generator/ absorber, a condenser, an evaporator and an expansion valve. The system ...
  • Hossain, Md Amzad (2013-12)
    This thesis describes the effort to experimentally verify the high performance characteristics of the co-flow jet (CFJ) airfoil. The CFJ utilizes tangentially injected air at the leading edge and tangentially removed air ...
  • Ferdous, Mausumi (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2012-09)
    Wind energy systems have become a focal point in the research of renewable energy sources. In this research provides a new concept of high performance, low cut-in speed wind turbine blade. To design the wind turbine ...
  • Kamruzzaman, Abu Sayed Md (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2007-12)
    Ship breaking is one of the most hazardous and dangerous occupation. Grave concern about the occupational safety and health problems caused by ship dismantling has been widely reported . Whilst many press articles have ...
  • Ali, Md. Hasan (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2013-11)
    Under the project work waste tire and tube of bicycle/rickshaw were converted to useful fuel oil by the process of pyrolysis. In doing so fixed bed lire tube heating pyrolysis technology has been applied. Thermal pyrolysis ...
  • Hossain, Md. Farhad (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2010-05)
    In this research a new concept of flow separation control mechanism has been introduced to improve the aerodynamic characteristics of an airfoil. Control of flow separation over an airfoil which experiences a laminar ...
  • Alam, Md.Ekhtiar (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh., 2010-08)
    Plant layout is the lifeblood of an industry as well as of any cement industry for its manufacturing process and layout design. A cement industry uses various types of machinery and equipment for its smooth operation. ...
  • Saha, Subrata (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2009-12)
    In this project work an attempt has been taken to predicting the effects of process parameters on weldment characteristics in MIG welding with the help of artificial neural network technique. Electrode wire diameter, ...
  • Asaduzzaman, B. M. (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2007-12)
    Electrochemical Grinding (ECG) process is a mechanically assisted electro-chemical process for material processing. The process is able to successfully machine electrically conducting harder materials at faster rate with ...
  • Mamun, A. H. M. Abdullah Al (Khulna University of Engineering & Technology (KUET), Khulna, Bangladesh, 2016-03)
    In recent years, intelligent or smart structures and systems have drawn more and more attention. Bonded structures are playing a key role as active components in many fields of engineering and technology. Mechanical stress ...

View more